IAG Stage 2 CNC Ported EJ25 11mm Oil Pump for 04-21 STI, 02-14 WRX, 05-12 LGT, 04-13 FXT

SKU: IAG-ENG-2240

IAG Stage 2 CNC Ported EJ25 11mm Oil Pump

The 11mm Subaru Oil pump is one of the most popular off the shelf pumps to use on EJ25 engines. Originally equipped on the 2008-21 STI Dual AVCS engines, it provides an adequate amount of pressure and flow that fits the needs of many OE and built engines. But, as with almost anything, there is room for improvement.

Increasing oil flow volume and pressure in an EJ25 ensures that the bearings have sufficient oil film under all power levels and driving conditions. Additional oil flow to the engine provides a greater oil reserve to operate the AVCS solenoids and cam gears - giving you more consistent performance results.

The IAG Stage 2 CNC Ported 11mm oil pump was developed over years of servicing street and racing engines. In that time IAG has tested and utilized the majority of the popular Subaru oil pumps available on the market (JDM, Cosworth, ACL etc.) for customer, personal and racing vehicles.

Over the last few years if you wanted an upgraded oil pump over the stock 11mm you would either buy a hand ported model from a trusted source, or often an OEM JDM (Japanese Market) 12mm pump. We believe that we have developed a better alternative. The IAG Stage 2 CNC Ported 11mm oil pumps have shown through lab testing on a Spintron Machine that it will outperform a JDM 12mm.

Stage 2 flows 11.1% more oil than the OEM 11mm Oil Pump

Stage 2 flows 9% more oil than the OEM 12mm Oil Pump

Stage 2 oil pressure is 12.4% higher than the OEM 11mm Oil Pump

Stage 2 oil pressure is 9.8% higher than the OEM 12mm Oil Pump

The Stage 2 Oil pump is a cost effective solution that outperforms the market standards. This pump has been extensively tested on street cars, track cars, and on our in-house Spintron to ensure consistent and repeatable performance.

Each IAG Stage 2 oil pump starts life as an OEM spec 11mm oil pump, straight from Subaru. IAG completely disassembles the new oil pump including pulling the rotors, backing plate & pressure relief valve. Next, the main body is fixtured in our in-house 5-Axis Centroid CNC machine where the inlet and outlet passageways are CNC ported. This allows for a larger, more consistent pathway for the oil into and out of the gerotor internals and helps to prevent cavitation. The Oil Pump Outlet where it meets the engine block is also CNC “Port Matched”, for a perfect transition into the engine block. The Inlet and Outlet sides of the gerotor are also opened up on the CNC mill to reduce inlet side cavitation, and to reduce outlet side pressure drops.

The pressure relief valve piston is REM Polished, which provides a non-directional, low Ra, polished finish. This reduces friction, heat and possibility of the relief valve piston galling and sticking, a common failure point on the OEM pumps.

The piston is reinstalled and confirmed to operate correctly. The rotors are measured and checked to be within the manufacturer's specification - aka Blueprinted, and installed next. The pump is then put together with a light coating of assembly lube to reduce friction and scuffing and aid in priming on first start up.

Finally, the backing plate is installed. Loctite is added to the hardware, and each piece receives a painted mark after it is correctly torqued. The pump ships ready to install, with all hardware and seals required for installation.

Features:

11mm Oil Pump Rotors

Shimmed and REM Polished Pressure Relief Valve

Measured, Blueprinted, and Assembled

Packed with assembly lube

Ships ready to install with all required hardware

CNC Ported to maximize flow & pressure and reduce cavitation risks

Tested to outperform other commonly available pumps

Designed for Single and Dual AVCS engines

Great for IAG Stage 2 and up built engines used for street and competition cars

Fits all EJ series Subaru Engines

Includes:

(x1) IAG 11mm Stage 2 CNC Ported Oil Pump

(x1) Front Crank Shaft Seal

(x1) Oil Pump O-ring

(x7) Oil Pump Zinc Plated Bolts

Recommended:

For use with IAG Stage 2 or higher (similar) engines.

Fitment:

04-21 STI, 02-14 WRX, 05-12 LGT, 04-13 FXT

VIP Motorsport is an official UK & European distributor of IAG Performance products. Our stock is directly linked with IAG USA, if the item is out of stock with us it could take up to 2-3 weeks to be received.